1

1

1
2

2

2
4

4

4
3.

3.

3.
  • ope体育江阴市大进塑料有限公司成立于2003年

  • 每年通过江苏省产品质量监督检验中心抽检

  • 共同推广和普及绿色PE管材的使用

  • 工厂占地70余亩,建筑面积3万多平方米

以技术为导向,以质量为生命,以服务为宗旨

我们将以严谨务实的态度制造出性价比最高的产品,以回报广大客户的支持与厚爱

产品

是一家专业生产高密度聚乙烯(HDPE)供水管件的企业

PE对接相等的三通63-800
PE对接相等的三通63-800
PE对接相等的三通63-800
PE对接红tee 450-800
PE对接红tee 450-800
PE对接红tee 450-800
PE对接RED-Tee 63-400
PE对接RED-Tee 63-400
PE对接RED-Tee 63-400
斜等三通110-630
斜等三通110-630
斜等三通110-630

ope官网滚球

质量——从专业

关于我们

ope体育江阴市大进塑料有限公司成立于2003年。是一家专业生产高密度聚乙烯(HDPE)供水管件的公司。它与中国著名的“西村一村”华西村相连。距离沿江高速华西出口仅2公里。沿江…以北

情况下

我们不断改进生产工艺和产品质量

城市管网建设

跨海管道施工

城市引水工程

地下主管道施工

新闻

PE管翻边观察热熔连接标准规范

PE管翻边观察热熔连接标准规范

热熔和电熔是焊接塑料管的常用方法。一种用热熔机对待焊接的两根PE管进行加热、铣削和加热,将PE管的端口熔化,用专用工具压紧,将两根PE管连接起来的方法。大口径pe管适用于这种热熔方式。电熔采用专用熔合管套,PE管件为专用热熔管件。管件上设有电热丝与外柱连接。电加热融化后,连接完成。施工方便,稳定性好,人工成本低。价格高,适用于小直径管道。PE给水管道的翻边是在管道焊接过程中通过挤压成形的。它通常被称为翻边和翻边。 The quality of the flanging also affects the flow efficiency of the PE pipe. Excessive flanging is also prone to scaling , Resulting in the breeding of microorganisms in the pipeline, silting in the drainage project, and reducing the efficiency of water flow. The reason for the inconsistent height of the pe water supply pipe flanges is that the water supply pipe is not level, uneven, and the heating area is uneven, which must be remelted. In the previous PE water supply pipeline construction, there is no good method to deal with internal flanging. Hengxing Management Industry summarized some of the reasons for the unqualified flanging of PE water pipes: Hot melt connection standard specification The connection of pe pipes and fittings should adopt hot-melt connection (hot-melt butt, hot-melt socket connection, hot-melt saddle connection) or electro-fusion connection (electro-fusion socket connection, electro-fusion saddle connection) and mechanical connection (lock Tight and non-locking socket connection, flange connection, steel-plastic over-connection). Pipes with a nominal outer diameter greater than or equal to 63mm should not be connected by manual hot-melt sockets, pipes with a wall thickness of less than 6mm should not be connected by hot-melt butt joints, and polyethylene pipes and fittings should not be connected and bonded by thread. Corresponding special connection tools should be used for various connections of pipelines. Open flame heating is strictly prohibited when connecting. The connection of pe pipes should be of the same grade, pipes and fittings of the same pressure grade, and the connections between pipes and fittings of different grades should be tested to determine whether they can be connected. When performing hot-melting or electro-melting connection operations in cold climates (below -5°C) or high wind conditions, protective measures should be taken, or the process parameters of the connection equipment should be adjusted. When connecting pipes, special cutters or pipe cutting tools should be used for pipe cutting. The cutting section should be flat, smooth, and free of burrs, and should be perpendicular to the pipe axis. Polyethylene (PE) water supply pipelines should be connected with pipes and pipes of the same manufacturer, material, and brand, and between pipes and fittings, and between pipes and pipes. Polyethylene pipes of different SDR series should not be welded. For connection, when pipes and fittings of different SDR series are welded to each other, it is advisable to make the welded joint wall thickness the same through mechanical processing. After heating, quickly remove the heating tool and check for damage.
迪

服务热线

+ 86 - 18961696788

关于我们

产品

联系我们

呃

地址:江苏省江阴市路桥天佑工业园区共镇路6号
电话:
+ 86-510-86378220
传真:+ 86-510-86376861
电子邮件:gjl@jydjsy.com/369421945 @qq.com